Procedures Module Configuration for Manual Result Entry

From OpenEMR Project Wiki

Preface

The goal of this guide is to provide a set of step-by-step instructions for setting up the Procedures Module to enter diagnostic results by hand. Doing so brings this data into the Encounter Form and closer to the clinical note.

Configuration necessitates meticulous attention to detail and order of execution. Once properly configured, deployment is relatively simple by comparison.

It is possible to upload a scanned image of results into Decuments/Medical Record, but that will place the data at a further distance from the clinical note.

To transmit orders and receive results from an external laboratory facility, refer to Laboratory Exchange User Documentation.

Facility

Despite the fact that no orders will be transmitted to an external facility; it is necessary, however, to manufacture a fictitious Lab Service in order to configure this module. The fictional facility must be entered in the Address Book first.

"Our Own Lab" will the Lab Service for the purpose of this exercise.

From the Menu on the left side bar, go to Procedures/Providers and add "Our Own Lab".

Lab.png

Configuration

The module can be set up for a panel of tests or for a single study. A panel will require a 3 tier process while it is only 2 for a single test.

Panel

Click the Configuration link and the "Add Top Level" button to begin. This button must be clicked each time a new panel or new single study is added to the list.

Lab1.png


The first tier, or level, of the configuration, will be the naming of the Group. Maintain the Sequence to keep the list in the desired order. Lab2.png


To begin the second tier of configuration, click the "Add" link. It may be necessary to scroll to the far right to see that link in the image below. Use "Edit" to modify configuration. To delete a setting, click "Edit" and go to the desired dialog box to delete the entry. Lab3.png


The second tier involves naming the Group as "Electrolytes" and assigning an Identifying Code to it. The choice of numerals or letters is at the discretion of the practice. Lab6.png

Lab7.png


Be certain that there is a "Yes" under the Order column and an Identifying Code as well. If these items are missing, it is a warning that the configuration had been faulty. The entries must be deleted and the process begun anew.

Click the "Add" link associated with "Electrolytes" to begin setting up Sodium. Scroll to the right if the image of the link is not visible. Lab8.png


The third tier will configure the first test of the panel, namely Sodium. Fields left empty are optional.

Lab9.png


Because mEq/L was missing; it had to be added in Administation/Lists/Procedure Units. Remember to make the addition Active before saving it. Lab10.png


It is helpful to have the range of values for a particular test in Discrete Result; but Recommendation, a third step of the third level configuration, is optional.

Lab11.png


A similar process is used to add the other tests of the panel. Again click the "Add" link associated with "Electrolytes" to begin. Scroll if need be. Pay close attention to Sequence; otherwise the tests will appear in alphabetical order; not Na, K, Cl, CO2 as physicians are accustomed. Lab12.png Lab13.png Lab14.png


A full panel should look like the following. Lab15.png

Single Study

Click "Add Top Level". A single test requires the naming of the Group and of the test. Lab16.png Lab17.png Lab18.png


Check that "Yes" and the code are present. Lab19.png

Procedure Order

Create an encounter. From Administrative, choose "Procedure Order". Lab20.png


Click in the designated area to search for the diagnostic study. Lab21a.png


Lab22.png


Click "Save and Transmit". Lab23a.png


Pending Review

To bring up the studies for result entry, login as Physician. Other staff, including Administrator, will not have the ability to perform this task. This can be changed in Administration/ACL. Lab24.png


Add the Reported date and assign a Status before clicking the "Sign Results" button. Lab25.png


Patient Results

After the signing the results, the data will appear in Patient Results. Lab26.png


Electronic Reports

This can be used to look up studies for a particular day. It is a good way to track tests which are lacking results. Lab27.png

Postscript

Configuration of the Procedures Module is a bit of a workout. Like all other aspects of OpenEMR, the more a physician masters; the greater his confidence and the deeper his appreciation of the magnum opus of the developers of this Project and all other Open Source projects as well.

Always frolick along the way.


Categories:Configuration Guide|User Guide|User Guide 4.1.0|User Guide 4.1.1|User Guide 4.1.2